1. BROMINE STARTER KIT:

1. When preparing or using this product, take care not to splash, drip or use on surfaces such as ceramic tile, linoleum, formica brand counter surfaces, carpeting, etc. as etching or discoloration of these surfaces may take place.

2. This product is intended only for use as a pool and spa filter cleaner.

SAND FILTERS:

Turn off inlets and outlets for all chemical feeders. Close main drain and place filter in backwash position. Slowly add 1 pint of this product through strainer while backwashing. This product can also be added through the sand fill port. Run filter until product begins to come out of the backwash water or until the product is seen through a filter viewing cell. Soak filter for 30 to 60 minutes. After soaking, backwash filter until water comes out clean and foam clears. Reverse procedure and start normal filter operation. For sand filters containing more than 150 pounds of sand, add 1 quart of this product.

CARTRIDGE FILTERS:

Stop filter operation. Bleed off excess pressure through the filter safety valve. Open filter unit, remove cartridge from filter, and rinse excess loose dirt with a water hose from top to bottom. Place cartridge into a bucket and add 1 pint of this product and 2 1/2 gallons water. Make sure filter unit is completely covered by the cleaner. Soak 30 to 60 minutes. After soaking, rinse with hose at maximum pressure to remove excess filter cleaner or until foam residue is completely washed off. Re-install cartridge and resume normal filter operation.

DIATOMACEOUS EARTH FILTERS:

Stop filter operation. Bleed off excess pressure through safety valve. Remove filter elements (grids) from filter and rinse off excess dirt with a hose from top to bottom. Place grids in a bucket and add 1 pint of this product and 2 1/2 gallons water. Make sure grids are fully immersed in cleaner. Soak 30 to 60 minutes. After soaking, rinse out excess filter cleaner with hose at maximum pressure. Re-install grid and add new filter media. Resume normal filter operation.

2. CHLORINE STARTER KIT:

FILLING & DRAINING

1. Fill Spa & Hot tub to the correct water level (at least halfway up the top skimmer/filter opening)
2. Test pH and Alkalinity using Test Strips at least weekly.
3. pH should be between 7.2 to 7.8; total alkalinity should be between 80 to 140 ppm; water/calcium hardness should be between 200 to 400ppm.
4. If not, make the needed adjustments using pH Increaser, pH Decreaser & Alkalinity Increaser, and Calcium Increaser accordingly
5. Use Stain & Scale to prevent & remove mineral scale buildup and to protect your spa components
6. Add Chlorinating Granules to dissolve contaminants in your water quickly.
7. If your spa is not Chlorine compatible, try our Bromine Spa Starter Kit
   

SANITIZING

1. Maintain the recommended chlorine level at all times.
2. AquaDoc Chlorinating Granules recommends maintaining 3-5ppm of FAC (free available chlorine) while the hot tub/spa is in use.
3. Test the chlorine level regularly, especially before and after each use.
4. Add Chlorinating Granules as needed to achieve proper levels

WEEKLY

1. Test water using Test Strips; adjust total alkalinity, pH levels, and calcium hardness using pH Increaser, pH Decreaser, Alkalinity Increaser & Calcium Increaser accordingly
2. Add Chlorinating Granules when necessary
3. Add Water Clarifier to defend against cloudy water
4. Add Spa Defoamer to get rid of foam
5. Add Chlorine Free Shock after every use to quickly oxidize contaminants

IMPORTANT! Circulate your Spa or Hot tub water for at least a few minutes after any chemical addition and before adding another product. Please follow the instructions on the container of each chemical in the kit carefully for maximum results and safety!

How often should I test and adjust my spa's pH and alkalinity levels?

It's recommended to test the pH and alkalinity levels at least weekly. Maintain pH levels between 7.2 to 7.8 and total alkalinity between 80 to 140 ppm using the appropriate AquaDoc products in the kit.

What is the ideal chlorine level for my hot tub or spa, and how can I maintain it?

To ensure proper sanitization, maintain chlorine levels between 3 to 5 ppm of free available chlorine (FAC). Regularly test the chlorine levels and adjust accordingly by adding Chlorinating Granules as needed.

How do I handle cloudy water and foam in my spa or hot tub using the AquaDoc Chlorine Starter Kit?

AquaDoc's Water Clarifier effectively combats cloudy water, while the Spa Defoamer helps eliminate unwanted foam. Follow the usage instructions on the containers for optimal results and safety.